Toro Lawn Mower Wheels: Fitment, Tooth Count, and Spec Breakdown

Best for: Standard 22-inch front-drive Recycler decks

Pros

• 3/4-inch hub offset
• Aging-resistant rubber composite
• Broad Recycler model fitment

Cons

• Tooth count omitted in listing
• Unfinished exterior finish

The CheeMuii 119-0311 Lawn Mower Wheel 2 provides a direct-fit replacement package engineered specifically for 22-inch self-propelled Toro Recycler mowers. Supplied as a pair of eight-inch push mower front drive wheels, this set replaces factory OEM part numbers 119-0311, 137-4832, and 115-2878, as well as the Stens 205-360 aftermarket cross-reference. Each wheel features an eight-inch outer diameter, an industry-standard 1/2-inch axle bore size, a pitch circle diameter of 0.5 inches, and a 3/4-inch hub offset designed to seat against the front drive axle assembly without rubbing the deck skirt. The listing specifies an impressive load index rating of 10000, underscoring structural durability for standard residential mowing duties.

This replacement wheel set is built using a combination of high-quality plastics and rubber designed for antifriction performance, aging resistance, and high temperature tolerance during extended summer cutting sessions. The listing notes an unfinished exterior finish and confirms compatibility with a massive array of Toro equipment, spanning classic series numbers like the 20001, 20003, 20005, and 20007 up through popular modern platforms including the 20330, 20331, 20339, 20350, 20370, and 20954. When maintaining your residential turf equipment alongside a thorough toro lawn mower inspection, verifying these front axle dimensions ensures proper transmission alignment.

For operators needing to eliminate front-end tracking wobble, this assembly targets owners of older and mid-generation 22-inch Recycler mowers experiencing lost forward momentum. However, while the physical casing matches OEM geometry, the listing does not specify the exact internal gear tooth count. Buyers requiring verified gear tooth specifications for steep incline operation may prefer models with explicitly documented drive tooth counts.

• Direct replacement for OEM numbers 119-0311, 137-4832, 115-2878, and Stens 205-360
• Standard eight-inch diameter with 1/2-inch bore and 3/4-inch hub offset
• Composite construction utilizing high-temperature, aging-resistant plastics and rubber
• Extensive compatibility spanning Toro Recycler models from 20001 through 20959

Best for: Super Recycler owners needing metal gears

Pros

• 42-tooth metal drive gear
• 1-3/4 inch hub offset
• Six-month warranty support

Cons

• Limited to rear drive
• Not compatible with standard Recycler

The 8″ Drive Rear Wheel for Toro from SutmorlyParts delivers a heavy-duty mechanical solution configured for Toro Super Recycler platforms. Sold as a two-pack, this eight-inch rear drive assembly replaces OEM part number 107-3709. Engineered specifically for rear-wheel-drive configurations, the critical highlight of this wheel is its integrated metal drive gear fitted with 42 teeth. This metal gear interfaces directly with the rear axle drive pinions on premium Toro mowers, ensuring positive mechanical engagement even under heavy load.

Dimensional specifications on this wheel include an overall diameter of eight inches, a rim width of two inches, an axle bore diameter of 1/2 inch, and an extended hub offset of 1-3/4 inches. The pitch circle diameter and wheel backspacing are both listed at eight inches. Built from durable plastic with tough outer wheel tread to maximize ground traction, this wheel assembly is backed by a six-month warranty service. Compatibility covers high-end Super Recycler walk-behind models including the 20053, 20054, 20055, 20056, 20057, 20058, 20062, 20090C, 20091, 20092, 20093, 20095C, 20099, 20380, 20381, 20383, 20384, and 21381.

This assembly suits homeowners whose Super Recycler mowers have ground down their factory drive teeth or developed loose rear hubs. The 42-tooth metal gear construction offers elevated resistance to gear stripping compared to plastic assemblies, making it ideal for thick turf and bagging operations where rear axle weight increases significantly. It gives way to other models when servicing front-wheel drive decks or machines requiring a 38-tooth drive configuration.

• Replaces factory part number 107-3709 on Toro Super Recycler decks
• Equipped with a durable metal drive gear featuring 42 precision teeth
• Engineered with an eight-inch diameter, two-inch width, 1/2-inch bore, and 1-3/4-inch hub offset
• Includes two rear wheels supported by a six-month after-sales warranty

Best for: Steep slopes needing verified gear traction

Pros

• Reinforced 53-tooth gear
• Anti-crack polypropylene core
• Diamond-claw rubber tread

Cons

• Front wheel drive only
• Two-pack only

The 8″ Front Drive Wheels for Toro manufactured by SENZHAO provides an exact OEM replacement pair for front-wheel-drive 22-inch Recycler mowers. Replacing Toro part numbers 119-0311, 137-4832, and 115-2878, these eight-inch assemblies are machined to original specifications to prevent wheel wobble, hub misalignment, and installation failures. The core architecture combines an anti-crack polypropylene core with an aggressive diamond-claw rubber tread engineered to resist garden debris, UV degradation, and excessive tread wear.

Mechanically, these wheels feature a 1/2-inch bore diameter, a 3/4-inch offset hub, a two-inch rim width, and a pitch circle diameter and backspacing of 0.75 inches. Crucially, the listing documents a built-in 53-tooth reinforced drive gear that bites smoothly into the transmission pinion. This solves the persistent operational issue of worn factory drive teeth slipping when pulling up hills or rolling through wet grass. Installation requires no specialized tools: operators simply extract the axle cotter pin with a wrench, remove the degraded wheel, and slide the new assembly onto the spindle.

This wheel set suits operators of 22-inch Toro Recycler models—including the 20330, 20331, 20339, 20350, 20351, 20370, 20377, 20378, 20954, 20959, 21378, and 21761—who require documented 53-tooth gear precision. Because it supplies both front wheels in a single package, users can replace both sides simultaneously to ensure equal traction and eliminate pulling to one side. It yields to larger high-wheel units when servicing mower decks with eleven-inch rear wheels.

• Direct cross-reference for OEM numbers 119-0311, 137-4832, and 115-2878
• Built-in 53-tooth reinforced drive gear restores climbing traction on slopes
• Anti-crack polypropylene hub core paired with diamond-claw rubber tread
• Precision 1/2-inch bore with 3/4-inch hub offset for drop-in cotter-pin installation

Best for: High-wheel Recycler variable terrain mowing

Pros

• 11-inch high-wheel diameter
• Extended 2-1/2 inch hub
• Durable metal construction

Cons

• Incompatible with 8-inch decks
• Heavier 3.8-pound weight

The 2 Pack 11″ Drive Wheels by shiosheng introduces large-diameter rear mobility for high-wheel Toro Recycler platforms. Sold as a set of two drive wheels, this assembly replaces Toro OEM part numbers 137-4837, 115-2885, and 119-0313. High-wheel mowers rely on extended rear rim diameters to roll over surface depressions, thick thatch, and irregular turf contours with significantly reduced operator effort.

The technical dimensions specified in the listing define an 11-inch diameter rear wheel with a tread width of 2-1/8 inches, an axle bore of 1/2 inch, and an extended hub length of 2-1/2 inches. Under the product specifications, the wheel backspacing is listed at 11 inches, the pitch circle diameter is 0.5 inches, and the assembly carries a load index of 90 with an item weight of 3.8 pounds. The material type is specified as metal, providing a rigid structural backbone designed for rugged operation. Bolt-on installation requires only a standard wrench to secure the wheel to the rear axle pivot plate.

This model is purpose-built for owners of high-wheel Toro walk-behind mowers, specifically models 20339, 20378, 20959, and 21329. Unlike universal outdoor equipment components cataloged alongside general craftsmen lawn mower parts, these wheels meet Toro’s proprietary high-wheel hub offset. Homeowners operating on hilly or undulating properties will benefit from the leverage of an 11-inch diameter wheel, though it cannot be installed on standard eight-inch rear mower decks.

• Replaces OEM high-wheel part numbers 137-4837, 115-2885, and 119-0313
• Substantial 11-inch diameter with 2-1/8-inch width and 2-1/2-inch hub length
• Durable metal material construction with an aggregate weight of 3.8 pounds
• Engineered specifically for high-wheel Toro Recycler models 20339, 20378, 20959, and 21329

The Lawn Mower Wheels 8″ FWD 140-2358 from Nuphtun is a genuine-specification front-wheel-drive replacement component engineered for the latest generation of 22-inch (55cm) Toro Recycler walk-behind mowers. Packaged individually as a single-wheel unit, this assembly directly replaces OEM part numbers 140-2358, 1402358, and 2358. It is manufactured to match the original factory balance, rolling resistance, and drive tolerances required by contemporary Toro walk-behind chassis.

Dimensional metrics include an eight-inch diameter, a two-inch rim width, and an eight-inch rim size. Uniquely, the listing specifies a wheel backspacing of four inches, differentiating its hub geometry from earlier generation Recycler front wheels. Constructed from premium plastic and rubber, this assembly is engineered specifically as an 8-inch FWD (Front-Wheel Drive) unit for 55cm Recycler S55OST and S55AWST baggers. Verified deck compatibility includes Toro model 21445 parts, as well as models 21442, 21447, 21472, 21770, and 21774.

This replacement wheel serves operators of modern Toro walk-behind mowers who need to replace a damaged front wheel without altering factory drive ratios. The listing explicitly cautions that this wheel is designed strictly for front-wheel drive applications and will not function as a rear drive wheel. For owners of current-generation 21445 or 21770 series mowers, it offers a direct drop-in repair to restore smooth rolling and positive front drive bite.

• Replaces modern Toro OEM part numbers 140-2358, 1402358, and 2358
• Engineered with an eight-inch diameter, two-inch rim width, and four-inch backspacing
• Constructed from premium plastic and rubber for high traction and smooth rolling
• Designed specifically for modern 22-inch / 55cm Recycler models including 21445, 21442, and 21770

Best for: Classic Recyclers with factory plastic gears

Pros

• 38-tooth wear-resistant gear
• 1-3/4 inch hub offset
• Includes two drive wheels

Cons

• Incompatible with metal-gear decks
• Limited to plastic-gear Recyclers

The 115-4695 Lawn Mower Rear Wheels Replaces assembly by WELOVEHOME offers a targeted drive wheel solution for rear-wheel-drive Toro Recycler mowers. Sold in a convenient two-pack, this eight-inch assembly replaces Toro OEM part numbers 115-4695, 138-3216, and 205-121. It features an integrated hard plastic drive gear fitted with 38 teeth, designed to mesh with the transmission drive pinions on specific older Toro chassis.

The physical specifications detail an eight-inch wheel diameter, a 1/2-inch axle bore size, an internal gear size of 3-1/5 inches, and a 1-3/4-inch hub offset. The wheel structure utilizes high-quality plastic paired with a tough rubber tire tread to optimize lawn grip during rear-drive engagement. Supported by a six-month warranty, this assembly is compatible with 22-inch / 55cm Recycler push mowers, including models 20332, 20332C, 20333, 20333C, 20334, 20334C, 20338, 20352, 20372, 20373, 20374, 20955, 20956, and 20958.

A vital engineering detail provided in the listing is that this wheel assembly utilizes a plastic drive gear identical to the factory original on older Recyclers. The manufacturer explicitly notes that if your Toro mower model originally utilized metal drive gears, these plastic gear wheels will not be compatible. For older machines that specify the 38-tooth plastic configuration, this assembly provides a dependable rear drive wheel replacement that prevents stripped transmission pinions.

• Replaces OEM numbers 115-4695, 138-3216, and 205-121 on 22-inch Recyclers
• Integrated 38-tooth hard plastic gear measuring 3-1/5 inches in diameter
• Standard eight-inch wheel diameter with 1/2-inch bore and 1-3/4-inch hub offset
• Supplied as a two-pack with rubber tires and backed by a six-month warranty